Html Drop Down Menus by Vista-Buttons.com v5.0.0

SUSPENSION BEAM SYSTEM

SWIVEL BEAM
  Html Drop Down Menus by Vista-Buttons.com v5.0.0 View/Print PDF

One way array


one way array



SPECIFICATIONS:

Material: Alloy Structural Steel Tube
Finish: Powder Coat Paint
Color: Black and Off-White
Working Load Limit: 300 lbs/136 Kg.
Design Factor: 10:1 ratio
Pack Count: 1/carton

OPTIONAL ACCESSORIES:

  1. Steerables Tilt Cable Kit controls tilt angle
  2. Many standard U-Brackets to choose from
  3. Adapts to most yoke mounts
  4. Add-on suspension eyebolt kits

One-Way-Array™

Suspension and Aiming for Single Cabinets

The One-Way-Array™ is an easy use load-rated and off the shelf loudspeaker rigging and aiming system for single loudspeakers. It is ideal for aiming sound in left and right of house configurations and provides spot coverage where speakers cannot be wall mounted.

The top section of the One-Way-Array rigs from two overhead suspension points. The lower section supports the loudspeaker and rotates relative to the upper section, horizontally. This gives

 

the installer precise horizontal aiming of sound.

For precise vertical aiming, select from a wide variety of U-Brackets or choose the Steerables® adjustable tilt cable kit system. Load rated shackles and eyebolts included in kit.

Typical venues include small to medium-sized theatres, churches, school auditoriums, gymnasiums, sport arenas, meeting halls and theme parks attractions.

Standard Configuration with Pull Back

SB-10 - 10” eye to eye   SB-18 - 18” eye to eye
SB-14 - 14” eye to eye   SB-24 - 24” eye to eye

Standard Configuration:

SAS-1WA-20 - 18” eye to eye, 3 x 3 configurations

DIMENSIONS:
standard configuration One way array
standard configuration One way array   standard pull-back configuration

Standard
Configuration

  

Standard Pull-Back
Configuration
 

Part Number

 A B C D E F
Standard SAS-1WA-20 18.0" 20.0” 5.0” 5.25” 3.0” 3.0”
With Pull-Back SB-10 10.0" 13.0” 6.0” 8.5” 4.86” 4.45”
With Pull-Back SB-14 14.0" 17.0” 6.0” 8.5” 4.86” 4.45”
With Pull-Back SB-18 18.0" 21.0” 6.0” 8.5” 4.86” 4.45”
With Pull-Back SB-24 24.0" 27.0” 6.0” 8.5” 4.86” 4.45”



one way array with pull back   one way array with tilt cable kit   one way array with u-bracket

O N E - W A Y - A R R A Y
W I T H P U L L B A C K

  

O N E - W A Y - A R R A Y
W I T H T I L T C A B L E K I T

  

O N E - W A Y - A R R A Y
W I T H U - B R A C K E T
The SwivelBeam version of the One-Way-
Array offers permanent eye fittings and
a rear extended eye fitting for use as a
pull back. The top of loudspeakers are
primarily suspended under the lower eye
fittings with two wire rope assemblies
and a third wire rope is attached between
a back point of the loudspeaker and
the extended eye fitting, tilting the
loudspeaker downward.		   One-Way-Array’s standard configuration comes with eyebolts that secure to the upper and lower rotating arms. The entire assembly suspends from the upper eyebolts and the Steerables Tilt Cable Kit attaches to the lower eyebolts. Cable kits come in five different lengths to accommodate different down angles. The selected loudspeaker suspends from the cable kit and can be adjusted into any down angle.   One-Way-Array’s standard configuration comes with pre set holes in the lower rotating arm to accommodate standard Allen UBracket mounts. To install, simply remove the center bolt, attach the selected U-Bracket using included hardware then reassemble the center bolt. Attach the loudspeaker in between the U-Bracket and tilt into position.